43200 is a accurate and fast LCR meter can measure from 20Hz up to 2MHZ. The DC internal bias has been enhanced to ±40V. Such powerful machine will be the ideal choice for multiple scenarios in testing and production.

Two test mode enables consecutive measurements to be made with two different instrument parameters set. For example two AC measurements may be made at different frequencies or an AC and a Rdc measurement may be made.

An optional component Binning module may be specified which provides an interface to component sorting machines. Limits set in the instrument Binning mode enable a wide range of components to be sorted while the choice of isolated or non-isolated modules give interface flexibility.

The optional Scaleizer handler module provides PASS/FAIL and data synchronisation relay outputs for limit checked measurements. Two output signal configurations are available.

Up to 20 measurements set ups can be saved with user defined names for later recall.

May be externally controlled using the standard RS232, GPIB, USB or LAN interfaces.

• Test components from 20Hz to 2 MHz
• 0.1% basic accuracy
• < 25ms measurement time
• Parameters C, L, Z, Y, X, B, Rac, Rdc, G, Q, D, Ø
• Single or two test operation
• Up to four parameters may be displayed (two test mode)
• Drive level from 10mV to 2Vrms
• Scale mode with measurement target limits
• Operator mode with target limits
• ±40Vdc internal and external bias
• Measurement setup Save and Recall
• GPIB / IEEE-488, USB, LAN and RS-232 interfaces
• Handler Scaleizer module (Optional)
• Binning (Optional)
• Protection against charged capacitors
• Small size and light weight

Frequency Range	20 Hz to 2 MHz
Frequency Steps	5 Hz - 20 Hz to 1 kHz 50 Hz - 1 kHz to 10 kHz 500 Hz - 10 kHz to 100 kHz 5 kHz - 100 kHz to 1 MHz
Measurement Function	Impedance (Z) Phase Angle (Ө) Capacitance (C) Dissipation Factor (D) Inductance (L) Quality Factor (Q) AC Resistance (Rac) Reactance (X) Susceptance (B) Conductance (G) Admittance (Y) DC Resistance (Rdc) is an option (/R) on all models.
Series/parallel equivalent circuit	Any combination
Polar Form	Z + Ө, Y + Ө
Drive Level(AC measurements)	Open circuit: 10 mV to 2V rms Voltage step size: 10 mV (200 steps) Short circuit: 100 µA to 20 mA rms Current step size: 100 µA (200 steps) Signal source impedance: 100Ω
DC Bias Voltage	Internal ±40 Vdc External - up to ±40V may be connected via rear panel
Measurement Speeds	Four selectable speeds for all measurement functions Up to 50 measurements per second depending on test frequency and setup condition
Measurement Ranges	Z, R, X 0.01 mΩ to > 1 GΩ Y, B, G 0.1 nS to > 2 kS L 1 nH to > 2 kH C 0.01 pF to > 1 F D, Q 0.0001 to 9999.9 Phase Angle -180° to +180° Rdc 0.1 mΩ to > 100 MΩ
Basic Accuracy	0.1% varies with speed, frequency, AC drive level and impedance of device under test
Binning (Optional)	User programmable PASS and FAIL bins. 25 way D-type interface connector. Option /B1 (non-isolated) - Common 0V. Bin outputs 0 to 5V (nominal) with >10 mA current sink capability. Option /B2 (isolated) - Common 24V input. Outputs 0 to 24V with >10 mA current source capability.

/S1 option - Scaleizer (S1 type)

/S2 option - Scaleizer (S2 type)

/B1 option - Bin handler (non-isolated)

/B2 option - Bin handler (isolated 24V)